Відео

Well actually it's Depron not Correx, said the pedant! ua-cam.com/video/x9xGeBrLvdA/v-deo.html Thanks for watching, have a great day!

Yep, can't stand around flying all day!! Thanks for watching, have a great day!

You're welcome! Have a great day!!

Thanks Tom! The fuse is quite well made and some thought has gone into the EDF tube etc so I will do something with the remains!! Watch this space!

Hey thanks! I have some plans for this, first replacing the electronics with proportional gear. Have a great day!

As I mentioned the radio gear is not proportional!! Of course every club has at least one member who suffers from "digital throttle itus"!!

For sure! I will put new radio gear and see what can be done to get it to fly!

Words of wisdom there My Guru! 😉🤣🤣

Thanks Mario! I will make something out of the wreckage!!

AWWWWW! Poor Peter!!

Further investigation of the module, shows it has an IP5306 power bank charge/discharge controller, which only does 5V in and out, so the 5/9/12V spec must be fake - any comments?

@@TonyAbbey I don't believe it can output 5/9/12V. It does not support PD mode. Mine still works for the use I built it! Thanks for watching, have a great day!

Good to know, thanks for sharing.

No, not in my experience. Provided that the ESC's are identical and calibrated. I also built a twin EDF with no issues : ua-cam.com/video/1_Td_TzXwww/v-deo.html

Using a 3S 1500 mAh pack, if you fly "scale" like easily 15 minutes. If you rag it around the sky like a nutter, less! Thanks for watching, have a great day!

@@1nformatica Thanks for your fast response! Now, may I know which motors and propellers did you use?

@@rva1945 There are links to all the components used in the video description.

You're welcome! All donations gratefully received!! Have a great day!!

For some bizarre reason the ADC pin is not present on the processor. Both pins 5 & 6 seem to be removed on the EP2. There maybe other similar receivers that have the pin. Thanks for watching, have a great day!

You're welcome! I see no reason why it should not work with that receiver. Only difference is it has a reset button instead of a pad which will make soldering a bit more challenging! Have a great day!!

Well yes / maybe!! You can select CH2 to be serial Tx at which point CH3 will automatically change to Rx and cannot be changed. So you can have SBUS or CRSF on pins 2/3 and still PWM on CH1. CH4 &5 would be possible for PWM (I think) IF you can solder to the ESP8285 pins 18 & 19, there are no pads on the board I can see. This is beyond my megre soldering skills!!

@@1nformatica LOL! You can talk! You should see some of the disasters here, perpetrated by various individuals, depending on their respective levels of descent into Parkinson's! 😱🙄

@@theoztreecrasher2647 I usually have the dt's in the morning so wait for the afternoon when I can get my trembling in sync!! BTW which sbus "brick" are you using?

@@1nformatica 😂We can't even claim that excuse since most of us are banned from booze by the quacks! 😉 S-bus "brick"? Usually FrSky/Flysky/Radiolink S-bus mini receivers with the Radiomaster TX16S 4-in-1. There are 2 Radiomaster ELRS mini receivers here somewhere waiting. RP1 and RP2 I think. 1 has that little ceramic antenna.

@@theoztreecrasher2647 Sorry, my bad! I meant the DSM/SBUS "brick" usually with servos that you want to connect to in the model......

Thanks Mario! I am constantly amazed by what is possible these days!!

Hey thanks! Have a great day!

Hey thanks! We are located in Andalucía, Southern Spain. Have a great day!

Hey thanks! More nonsense here : ua-cam.com/video/vPrd4y8zIUk/v-deo.html Random fact, I was born near Papatoetoe!! Have a great day!

You're welcome! Have a great day!!

Hey thanks! I can't claim the launch mode as I nicked it from "Painless360"!! Have a great day!

It turned out better than I imagined when I opened the envelope!! Good fun, which is what it's about for me!!

Thanks Mario! It's a lot of fun!

For the first flight it was pitching up as I put too much reflex on the elevons. Second flight would fly straight and level at half throttle hands off. Will try the "dive test" for CG on the next outing! Thanks for watching, have a great day!

Thanks Martin, missing some additional footage!! See you soon!

I've forgotten how many pending projects I have!! Thanks for watching, have a great day!

Hey thanks! Have a great day!

drive.google.com/file/d/1VlCShq8hUUtPatXYvEwJ6bMc0LfcUQTq/view

Hola, Hay enlaces en el vídeo descripción. Un saludo desde Andalucia.

My guess is bad battery contacts or the switch pads are still dirty. Check for broken / bad solder joints on the battery connections and check the board is getting battery voltage with a meter (battery not flat)! Clean both the circuit board and contacts with alcohol, I use Isopropanol. lastly it's possible the LEDs are not making contact, again check for cracked solder joints / pads lifted. Good luck!

See the flight video here : ua-cam.com/video/OPIbe3jZpgY/v-deo.html

@@1nformatica thank

@@did3d523 You're welcome! Have a great day!!

Hola, haría una copia de tu modelo de helicóptero en el Radiomaster y usaría esa copia (en caso de que la estropees) para controlar tu simulador. De esa forma todas las mezclas que tengas deberían funcionar igual. ¡Un saludo desde Andalucía!

Gracias por responder llegue a la conclusión que puedo tener problema en la señal corregime si me equivoco logro hacer las mesclas lo trimo simple para sacar de dudas de inicio bien pero se enloquece como si se te rompiera un servi de golpe tanto ELE como Ail jugué con el centrado de los servos tampoco me recuerda a la controladora Aling 3gx antes de programar dejar todos los trim en cero si no hace esto ..bueno seguiré probando por lo menos tengo señal y obedece gracias te comento si lo logro

@@gerardopereyra3989 ¡Estoy feliz de que estés progresando! Sí, los giroscopios siempre complican estas cosas. ¡Buena suerte!

You're welcome! Have a great day!!

Hi, I think I was using "C" mode as when I switch to the other mode the plane is uncontrollable! I made another video here with the same result : ua-cam.com/video/9Fw-k2MiaPA/v-deo.html Thanks for watching, have a great day!

Hey thanks! Have a great day!

You're welcome! You can also control it from a multiprotocol module ua-cam.com/video/9Fw-k2MiaPA/v-deo.html Have a great day!!

Hey thanks! The video is available in 1080P 60fps, kindly check your "quality" settings at the bottom of the video window. Have a great day!

Hey thanks! My poor flying skills don't do it justice, but it IS a LOT OF FUN. Which is what matters to me! Have a great day!

Short answer, you can't! Long answer, the "original" firmware was based on the "Generic ESP8285 6xPWM 2.4Ghz RX". Since the ExpressLRS devs have decided to remove this target from the configurator it is no longer possible to build firmware for this Rx. I have successfully used the Happymodel EPW6 target. Configuring the 7th channel can be done with the "JSON" file as before. Thanks for watching, have a great day!

Right on! Thanks for watching, have a great day!

Thanks Mario! I think it looks good too!

Still don't know why the first baro didn't work. 🤔

Hey thanks! I was certainly more comfortable with it this time! Have a great day!

“Nose heavy planes fly poorly, tail heavy planes fly once”

Our field is right next to a dog rescue center! The barking is sometimes annoying but the young ladies that look after them make up for that!! Woof woof!! Thanks for watching, have a great day!

The cameraman did another great job tracking the aerobatic manoeuvres of the very competent pilot.......gr8 job ME 😂

@@MartinClarke-he1rh Thanks for your contribution as always!

That's a problem. Just speculating but maybe you can pass a thin piece of something like fishing line under it and pull it up?